BA 15 Automotive LED replacement brake/tail light bulbs - BAY15D (1157) series

The LED Shop offers LED replacement bulbs for nearly all car, truck, trailer, RV & caravan lights:
LED brake/tail lights, LED indicator bulbs, LED reverse lights, LED dashboard lights, LED overhead lights, LED glovebox lights, LED trunk lights
LED light bulbs - LED Auto Light Bulbs - led lights - low voltage lighting - 12v LED lights - LED Automotive
LED tail lights/LED brake lights - Inside, overhead, glovebox and trunk LED lights - LED park lights - LED trailer lights
LED truck lights - LED warning lights - motorcycle LED lights - motorcycle led tail lights - low voltage bulbs LED rv lights

We stock 6 Volt -12 Volt and 24 Volt bulbs - most of our LED replacement bulbs are 8-25 Volt DC multi voltage
Our replacement LED bulbs fit into existing car light fittings without any modification

Check or change
the contents of your shopping cart

What is the RoHs standard?

Australian Gst
and overseas shipping

General FAQs

Chris Whitley Singer/Songwriter
1960 - 2005

Easy secure payment with PayPal or our secure Credit Card gateway

Series BAY15D (1157)
Staggered Pins
Dual Pin Connection

BAY15D Brake/Tail Light

Overall Length: 49mm
Diameter At Widest Point: 23mm

for matching BA15 sockets click here

Frequently asked questions about this LED product

13 x 3 Chip HI-POWER RED SMD BRAKE/TAIL LIGHT
Manufactory part no: 1157, 3496, 2057, 1142, 12499, 12594, P21/5W

13 x 3 Chip Hi-Power SMD LEDs = 39 diodes used.

Extremly bright for cars with highly reflective brake lamp housing - 10 LEDs shine sideways and 3 LEDs shine directly back.

These LED tail/brake light replacement bulbs fit every BAY15D series dual pin bayonet fitting found in 12V automotive lighting.

For Motorcycles
Generally - we keep the White units for motorcycles only.
For cars RED LED behind Red lenses is best.
Motorcycles usually have a clear lens underneath for the registration plate and this makes it critical to use White.

For Motorbikes

For Cars

12V Hi-Power SMD LED Tail/Brake light 13 x 3 Chip RED SMD LEDs
(single bulb)
12V Product No: #0080
AUD$ 25.00 including GST

You can also order by Email Fax, and (Snail)Mail

Series BAY15D (1157)
Staggered Pins
Dual Pin Connection

Overall Length: 43mm
Diameter at Widest Point: 23 mm

for matching BA15 sockets click here

Frequently asked questions about this LED product

3 x 6 Chip HI-POWER RED SMD BRAKE/TAIL LIGHT
For non-reflective type lenses
Manufactory part no: 1157, 3496, 2057, 1142, 12499, 12594, P21/5W

We use 3 Chips with 6 layers in these units giving a total of 18 diodes.
Thermally these 6 Chip units will handle all conditions with the onboard heatsink and the spacing we've given them.
Using 6 layers gives intense light, with all the light coming from the end of the bulb we recommend these for non-reflective type lenses.
For reflective lenses please use the 13x3Chip units seen above.

You can also order by Email Fax, and (Snail)Mail

Series BAY15D (1157)
Staggered Pins
Dual Pin Connection

Brake effect (all bulb lights flashing on & off)

LED Spinner Bulbs

Tail light pattern
(6 lights spin around clockwise & anti clockwise)
Very recognisable at night due to movement

Length:43.6 mm
Diameter on top: 26.2 mm

for matching BA15 sockets click here

Frequently asked questions about this LED product

12 LED SPINNER BULBS
BRAKE/TAIL LIGHTRED

Customers please note:

Whilst these are 1157/BAY15D (dual pin bayonet fitting) found in most applications for 12V automotive lighting, it is important to note that they shouldnt actually replace the standard types seen further up the page. They make a great accessory brake light but by law your primary brake lights shouldn't flash OK?
LEDs spin in a circle in tail light mode- when brakes are applied the lights start flashing and continue to do so.

You can also order by Email Fax, and (Snail)Mail

Frequently asked questions about this LED product Click here for General FAQs

Are automotive LED bulbs as bright as standard incandescent bulbs?
Our full size 13x3Chip SMD LED bulbs equal the brightness of a standard 21w bulb, they're more outstanding at night however than a normal incandescent which will to look orange compared to it.
The white units have an "arctic blue" look to them and stand out against the Normal White incandescent reversing light which has a Yellow tinge.

Should red brake lights be used behind red lenses and amber behind amber?
Yes - the richness of the color is particularly noticed at night - you will find that your LED brake lights will make the other types look orange.
Of course clear lenses look excellent on your car and LED enables you to use them without those horrible painted bulbs.

How do I know what fits my car?
To date no supplier has been able to provide us with parts lists for cars. Basically all we need to know is the size of the base and the length/width of the bulb - we should be able to go from there.

Where can I get an LED version of the new BAU15S or BAZ15S bulbs?
At the moment, LED bulbs are unavailable in this pin configuration. We will be looking into these in the very near future.

Why do I have a bulb out light in my dash after installing LED bulbs?
European and newer model cars will often show a bulb out light as an LED bulb only draws between 1 and 5 watts. Your original factory issue incandescent bulbs draw at least 20 watts. Your car's electrical system interprets this lack of load as a bulb out. You can get around this by installing a flasher can.

website by
Klaus Waeschle

BA 15 Automotive LED replacement brake/tail light bulbs

BA 15 Automotive LED replacement brake/tail light bulbs - BAY15D (1157) series

Easy secure payment with PayPal or our secure Credit Card gateway

Automotive LED lights < BAY15D (1157) series LED Automotive Replacement Brake/Tail Bulbs

Products available:

13x3 Chip SMD LED brake/ tail light

3x6 Chip SMD LED brake/ tail light

Spinner bulbs

Series BAY15D (1157)
Staggered Pins
Dual Pin Connection